The PURPOSE of this release is:

New feature:

• PCTOOL-3799 : 1. Max run time , 2. Merging of flow calculation, 3. Add level sensor
• PCTOOL-3489 : 1. Cybersecurity -Removal of Ethernet password, 2. CIM selection menu remove, 3. Motor protection tripped, maximum number reset limit, 4. Foam drainage on specific time, 5. Mixer PTC, 6. Running on generator, 7. Flush from pit

The PURPOSE of this release is:

New feature:

• PCTOOL-1510:CR: DC, The range of "Calculation Delay" is not correct

Issues Fixed:

• BUG-3492:Language list not correct

The PURPOSE of this release is:

New feature:

• Support firmware Vx03.20.04.
• PCTOOL-1387 :: Advance flow and Grinder control updates.

The PURPOSE of this release is:

Issues fixed:

• GMA00119257 System overview section some data items are missing.

The PURPOSE of this release is:

Issues fixed:

• GMA00118582 WW:PC Tool WW AI Min, Max default value issue.
• GMA00118436 WW:Visual Studio 2013 IDE for PC Tool Waste Water.

The PURPOSE of this release is:

New feature :

• Ethernet communication settings:
  • Added new Ethernet configration “Retry”.
  • Added new Ethernet configration “Timeout”.
• Emergency Stop:
  • Added new DI enum “Emergency Stop”.
  • Added “Emergency Stop alarm” in system alarm.
• Advanced Flow(fixed speed):
  • Added new Flow calc. type enum “AdvancedFS”.

• Grinder control and Anti stealing:

  • Added new DI item:
    • Anti intrusion.
    • Flow switch, grinder.
    • Overcurrent, grinder.
    • Overtemperature, grinder.
    • Manual forward, grinder.
    • Manual reverse, grinder.
  • Added new DO item:
    • Intrusion alarm.
    • Start, grinder.
    • Reverse, grinder.
    • Grinder blocked alarm.
  • Added new Alarm item:
    • Intrusion (Door opened) (117).
    • Too many grinder reversals (115).
    • Grinder motor over temperature (116).

Issues fixed :

• GMA00117570 : PC tool WW: Active Alarms - Overtemerature Aalarm ID's are missing.
• GMA00116453 : PCToolWW: Crash Issue.
• GMA00116454 : PC Tool WW : Alarm Test Issue.
• GMA00110844 : WW:PC Tool WW - AI Min, Max default value issue.
• GMA00110886 : PC Tool WW - Analog OutPut Text Mapping Issue.
• GMA00103746 : DataLog Functionality screen text overlapping if adding more parameters.
• WW:PC Tool Mode of operation for the grinder.
• WW:PC Tool The total grinder operating time.
• WW:PC tool WW - Fixed Speed - Validation.
• WW:PC Tool ODBC Error.
• WW:PC Tool WW Fixed Speed - Sampling time Range.
• WW:PC tool WW - Flow Calculation - Pit area Tool Tip Issue.
• WW:PC Tool Com ports selection issue in Windows 10.

The PURPOSE of this release is:

New feature :

• Add new DO item “Dry running alarm”
• Add “Dry running alarm” in alarm relays
• Add new status for MP204 - “MP204, phase voltage Lx”
• Add new status for IO 11X - “IO 11X, support bearing” and “IO 11X, main bearing”
• Add new languages Slovenian, Croatian, Lithuanian, Indonesian, Latvia for Display language

Issues fixed :

• Display the MP204 parameters under PumpX monitor section if and only if MP204 installed.
• Display the IO 11X parameters under PumpX monitor section if and only if IO 11X installed.
• Dry running alarm setting validation which should be more like high level alarm setting
• GMA00104146 : PC Tool WW- Controller Not Responding error
• GMA00108274 : WW - Empty lines in monitor screen , system status

The PURPOSE of this release is:

New feature :

• Last PC Tool Configuration for Ethernet communication of CU 362
• Shared configuration feature for both CU 361 and CU 362
• Added Max_reverse_frequency parmaeter for VFD 1-6 from profile_version 5 and above

Issues fixed :

• Update WW Tool report with CU 36x instead of CU 361
• GMA00100369: Scaling issue on many installation folders
• GMA00100371: Shared folder finalization (only 1 pop-up and verification on “auto-detecting” name)
• Included phrases and phrase related feedback comments
• Included retry mechanism in case of failure during send and receive data in direct USB communication.
• UI messages partially appears while selecting different "Save to the controller" options under "Save settings"
• PC Tool crashes at end of loading configuration
• Setup id code related crash if new version of PC Tools installed on top of old GTI versions V3.01
• Change in currently loaded configuration even though there is no installation changes
• Configuration, Installation Label name missing.
• Phone book entry is created for Shared configuration and activated while adding new shared installation.
• Increased telegram retry count for usb batch write and update error
• Fixed CQ GMA00103101 : WW - Invalid data is saved to the controller
• Fixed GMA00103135 : WW : Message Box - Empty profile name while saving the configuration
• Fixed GMA00103136 : WW - Connect to shared Installation site not points to corresponding shared phone book entry

Known issues :

• GMA00103137 : WW : Serial Number ( Not in order) for Configuration
• GMA00103138 : WW - Unable to close invalid data window in Negative scenario. Neither the application can be closed
• GMA00103141 : WW - Error Batch Updating data items- Partially improved. But still issue is there
• GMA00103149 : WW Application hangs sometimes in a long run and also USB port is not detectable

The PURPOSE of this release is:

Waste water tool issues fixed :

• Unit scaling not works properly for Data Log's Tabular view and Grundfos report viewer
• Unit scaling not works for Litres to Gallons,Litres per second to Gallons per minute
• Online log, Offline log - Only units are scaled but not the values
• Counter inputs on IO351B-3 keeps being deselected every time the configuration is opened
• User-defined sensors cannot be seen in user-defined log
• Pit settings- level settings -spin control increment and decrement not works fine in US units
• Data log, Log viewer parameters always shown in SI units
• User defined parameters not appears in tabular view
• Data log- Info should be given to the user if no data available to draw graph
• In case of no parameter selected in Data log and in Online log then the "Load","SaVe" button options should not be allowed
• Invalid application icon in control panel Add/Remove programs

Known issues:

• Multiple installations are possible. It can provide Modify / Repair /Remove options
• Installer runs for 2 times
• Icons are different of installed exe. In the Add/Remove, icon color is black but it is blue at Desktop shortcut and in Start>Program
• Overlapping of legend and the graph (report viewer) once selected all parameters
• In case of same version installation multiple times, installer should throw a message "xx.xx" is already installed, Do you still want to install?"